This pint sized performer is based on the successful Stevens AeroModel SkyBuggy 300 platform. Reduced in size and re-engineered to readily accept ParkZone Ultra Micro 2.4 DSM2 electronics. The SkyBuggy 100 is right at home in your large backyard or gymnasium.
SkyBuggy (100) echos the nostalgic lines of the long since discontinued Andy Clancy Lazy Bee model line and features a refreshing splash of Kris Cartwright's own keen eye for design. When the above is combined with Stevens AeroModel's modern model engineering, clear and thoughtful instructions, and state of the industry cutting techniques the result is simply fantastic on all levels.
Features: Interlocking Laser Engineered™design frames in two evenings or less. Precision cut from hand selected AAA balsa and hardwoods. Designed to readily accept E-Flite and ParkZone Ultra Micro Electronics Hardware package includes control linkage. Thick flat-bottom airfoil nets high-lift and stability. Well mannered, predictable, and positively stable flight envelope. Ideal for dawn and dusk patrol sorties - or just cruising the weed patch behind your house.
Basic modeling tools including #11 razor blades and knife, medium and thin CA, CA applicator tips, adhesives, sanding block.
2 per package
Light weight design
2.14 gr. per wheel
Ideal for indoor and park flyers. Du-Bro RC Mini Lite Wheels are lightweight and features a 2 piece press together hub and a super light foam tire. Comes standard with .047 axle hole and can be drilled out for larger diameter axles.
These Mini Lite Wheels are sure to give your airplane that scale look.
This OEM ParkZone PKZ3352/U1152 Ultra Micro Receiver/ESC/Servo "puck" is a factory replacement unit for the ParkZone Vapor, Ember 2, HobbyZone Champ and many other Ultra-Micro model aircraft distributed by Horizon Hobby. The PKZ3352 is compatible with all ParkZone, E-Flite, HobbyZone, and Spektrum DSM2 compatible 2.4ghz transmitters. This product will not fuction with Airtronics, Futaba, Hitec, or other non DSM2 compatible transmitter.
The PKZ3352 weighs 3.3g and features an on-board receiver, electronic speed control (ESC), and servos mapped to Elevator (pitch) and Aileron (roll) transmitter channels. This configuration is Ideal for control of Rudder/Elevator three channel models. Two linear drive servos built atop a receiver/esc "puck" featuring a pre-soldered battery connector and motor plug.
Ultra Micro Propeller (2/pkg) - 130mm x 70mm. This propeller was designed for the E-Flite 4-Site and is same propeller used by the UM P-51 by ParkZone. Also recommended for all micro models by Stevens AeroModel that utilize the PKZ3624 Motor and Gearbox. Package includes one 130mm x 70mm propeller with foam rubber spinner.
(Note: propeller is installed by threading onto the output shaft of the pKZ3624 gearbox.)
These are a major upgrade for Eflite, ParkZone Ultra Micro and Kyosho Minium series micro RC models, and fit either without modification. With Hyperion's G3 technology inside, they deliver more mA per gram than the stock batteries, while sustaining higher voltage under high loads, for greatly improved power performance. Of course, like all Hyperion G3 Lipo they last for hundreds of cycles, with consistant performance, when properly charged and stored.
The fact that they can be safely charged at up to 5C rates - for charge times as low as 10 to 12 minutes - is just icing on a very tasty cake.
ZAP CA Is the thinnest CA in the ZAP product line. The penetrating or wicking ability of this glue makes it a favorite of modelers around the world. Balsa wood is bonded almost instantaneously, with the glue sometimes traveling several inches into the parts.
SUPERIOR PENETRATING FORMULA
SUPER THIN - WATER LIKE CONSISTENCY
BONDS AND CURES IN 1 TO 5 SECONDS
WORKS ON MOST MATERIALS
ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequaled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. Wood, plastic, metal, glass, ceramic, fabric, rubber, fiberglass, carbon fiber, or any combination of, ZAP-A-GAP CA+ can help solve many tough bonding problems.
SUPERIOR GAP FILLING FORMULA
MEDIUM VISCOSITY ALLOWS APPROXIMATELY 7 TO 10 SECONDS FOR PART POSITIONING
AVERAGE OF 20 SECONDS FOR CURING
WORKS ON OILY SURFACES
USE ZIP KICKER TO ACCELERATE CURE TIME
Flexi-Tips by ZAP brand CA glues fine tip is suitable for thin and medium weight CA and allows for Smaller Drops, Precision Application, Extension into hard-to-reach areas, Maximum use of bottle. Universal! fits most brand's CA bottles.
This a great little item. Sanding block is made from very high density foam and features fine 240 and extrafine 120 grit papers. This block won't deform and cause waves in your project like those cheap hardware store sanding sponges.
Got the opportunity to fly this at a local indoor get together. It is so predictable and is VERY resilient to damage, spot landings on tables and crashes into the table didn't faze this little guy! Don't let foam rule your indoor world, get back to building and realize the fruits of your labor.
Hi, I received my Helium mg2 kit yesterday, and I will have it ready for covering tonight. I have built a few laser cut kits but yours is the best by far. The accuracy of the parts fitting and the completeness and accuracy of the instructions is u...
— Tom Watson
Just finished building my 3rd micro kit, had fun doing this kit like the other 2 kits I built. The Fly Baby I built is a kick in the*** to fly, I just hope the new kit of the Heath LNB 4 is as much fun to fly. so if you like the challenge of build...
— Tony Scavello
I have to say that the MBP program is one of the best hobby investments I have made.
I LOVE your site, as well as the quality, attention to detail and passion that you put into all of your products and kits. You are lightyears ahead of everyone else in this niche and are the reason I got back into building! Thank you!
Just finished my LiddleGee. What an impressive micro plane. I've built alot of planes, big and small, but I got more satisfaction from this kit in a week of evenings then I've had in years. Excellent design, excellent quality, quite a nice surpri...
Wow! Great service. I got the part today. Thank You!
— Ira Meltzer
You guys make the best stuff. Don't really know how else to phrase it. I have half a dozen of your kits and they're all great. If I ever forget that flying is supposed to be fun, all I have to do is grab my Lil Squirt or my Sky Buggy and head out ...
— Kevin Peltz
I finished building the Fly Baby, only thing I need is the radio block. This was another enjoyable kit to build, ...and am thinking about picking up another kit to start on. Good job guys, keep up the good work.
— Tony Scavello
Outstanding! I just finished the Fokker D7 and gave it a test flight. I had not worked with balsa since I was a kid(too many years ago). Yours is the best kit I have ever seen. I purposely took my time because it was so enjoyable and I especially ...
— Fernando Engelsma
Just finished building the 4Charlie airplane. As always, the plans, instructions, and photos are top-notch and the laser parts (I purchased those) were accurate to the plans. The plane really flies well and is stable in light winds. I did u...