Grab Snoopy and the boys and get ready to do battle with the Baron as Stevens AeroModel unveils the latest release in our micro laser cut RC model line, the venerable SE5a. The Royal Aircraft Factory SE5a was perhaps one of the most famous British fighter aircraft of the Great War. With inherent stability, maneuverability, and speed (at the time, faster than anything Germany could throw at it). The SE5a left it's mark upon history and many a German fighter.
Two Pack of Ultra Micro Propellers (with small foam spinner) 130mm x 70mm this propeller was designed for the E-Flite 4-Site and is same propeller used by the UM P-51 by ParkZone. Also recommended for the LiddleRod, PuddleBug, and S-POU! micro models by Stevens AeroModel.
This OEM ParkZone PKZ3352/U1152 Ultra Micro Receiver/ESC/Servo "puck" is a factory replacement unit for the ParkZone Vapor, Ember 2, HobbyZone Champ and many other Ultra-Micro model aircraft distributed by Horizon Hobby. The PKZ3352 is compatible with all ParkZone, E-Flite, HobbyZone, and Spektrum DSM2 compatible 2.4ghz transmitters. This product will not fuction with Airtronics, Futaba, Hitec, or other non DSM2 compatible transmitter.
The PKZ3352 weighs 3.3g and features an on-board receiver, electronic speed control (ESC), and servos mapped to Elevator (pitch) and Aileron (roll) transmitter channels. This configuration is Ideal for control of Rudder/Elevator three channel models. Two linear drive servos built atop a receiver/esc "puck" featuring a pre-soldered battery connector and motor plug.
These are a major upgrade for Eflite, ParkZone Ultra Micro and Kyosho Minium series micro RC models, and fit either without modification. With Hyperion's G3 technology inside, they deliver more mA per gram than the stock batteries, while sustaining higher voltage under high loads, for greatly improved power performance. Of course, like all Hyperion G3 Lipo they last for hundreds of cycles, with consistant performance, when properly charged and stored.
The fact that they can be safely charged at up to 5C rates - for charge times as low as 10 to 12 minutes - is just icing on a very tasty cake.
ZAP CA Is the thinnest CA in the ZAP product line. The penetrating or wicking ability of this glue makes it a favorite of modelers around the world. Balsa wood is bonded almost instantaneously, with the glue sometimes traveling several inches into the parts.
SUPERIOR PENETRATING FORMULA
SUPER THIN - WATER LIKE CONSISTENCY
BONDS AND CURES IN 1 TO 5 SECONDS
WORKS ON MOST MATERIALS
ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequaled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. Wood, plastic, metal, glass, ceramic, fabric, rubber, fiberglass, carbon fiber, or any combination of, ZAP-A-GAP CA+ can help solve many tough bonding problems.
SUPERIOR GAP FILLING FORMULA
MEDIUM VISCOSITY ALLOWS APPROXIMATELY 7 TO 10 SECONDS FOR PART POSITIONING
AVERAGE OF 20 SECONDS FOR CURING
WORKS ON OILY SURFACES
USE ZIP KICKER TO ACCELERATE CURE TIME
Flexi-Tips by ZAP brand CA glues fine tip is suitable for thin and medium weight CA and allows for Smaller Drops, Precision Application, Extension into hard-to-reach areas, Maximum use of bottle. Universal! fits most brand's CA bottles.
This a great little item. Sanding block is made from very high density foam and features fine 240 and extrafine 120 grit papers. This block won't deform and cause waves in your project like those cheap hardware store sanding sponges.
AeroLITE (SOLITE) Olive Green, 11 in. x 27.5 in. (275mm x 700mm). Folded package.
Ultra light iron-on self-adhesive film (polypropylene) for electric indoor and micro model aircraft. Now offered in convenient PatchPak size; just the right amount for repair jobs, trim, or covering our micro and ultra-micro model aircraft kits. Transparent colors weigh only 20 grammes per square meter (0.60 ounces per square yard). 'Solid' colors are only slightly heavier. Weights include color and adhesive.
Film is folded into packages not rolled. Minor creases from packaging will readily iron out as film is applied to model.
Vinyl graphics pack for ultra-micro SE5a "Rondels" are pre-printed and CNC cut ready for application to your model. Package Includes two AeroLITE (SOLITE) 11 in. x 27.5 in. (275mm x 700mm) PatchPaks in Olive Green.
I have built the SE5a and the D7Fokker. Both fly great but I had to add 1/4 oz to the nose of both to get the balance right. They were a dream to build and cover with Aerolite. I am just finishing the QuickOats 250, I hope it flys like my 84" Quaker.
Some of the best plan details I have seen with clear instructions. The laser cut balsa is a dream to work with as the parts fits perfectly with no adjustments needed. (I remember the balsa kits I worked with in my younger days with pins and glu...
— George Grueber
I have been trading your (micro) kits to a young man (12 years old) for yard work. I think I've created a new model builder !!! He loves it. Another friend, who only flew 3/D worked together with me building your "Helium MG2" glider. We couldn...
— Norm Smith
Been building balsa kits for 68 years and your FredE and Sky Buggy are the greatest, most fun to build kits I have ever built.
— Rick Spangenberg
I've just finished building the Micro Hergt Monoplane, which is the 2nd of your kits that I've built. Based on the quality of the 1st kit, the Puddle Bug, I've bought several others. I am seriously impressed with the level of engineering that has ...
— Don Rice
I recently purchased the pond flyer ... this has to be the best wood kit we have ever assembled...
— Andy Langam
Just finished building my 3rd micro kit, had fun doing this kit like the other 2 kits I built. The Fly Baby I built is a kick in the*** to fly, I just hope the new kit of the Heath LNB 4 is as much fun to fly. so if you like the challenge of build...
— Tony Scavello
I finished building the Fly Baby, only thing I need is the radio block. This was another enjoyable kit to build, ...and am thinking about picking up another kit to start on. Good job guys, keep up the good work.
— Tony Scavello
I just built the BuzzBomb 400 and test flew it. Building it was really enjoyable because of the precisely cut parts and detailed instructions. The plane flew just as you said it would. It floats through the air with the greatest of ease and will b...
— Mark U.
I LOVE your site, as well as the quality, attention to detail and passion that you put into all of your products and kits. You are lightyears ahead of everyone else in this niche and are the reason I got back into building! Thank you!
I would like to start by saying that I have been a customer for many years. I have always enjoyed every kit and they have all been very well designed and fly as expected and sometimes better! In my honest opinion it is your customer service that i...