Now shipping! Nostalgic lines reminiscent of the venerable Quaker free flight model line. We reduced this flying classic to 100 square inches and added a touch of "Toon" charm. Well behaved and easy to fly indoors and out! Designed to be flown using popular 2.4ghz ultra micro electronics from the ParkZone line of model aircraft.
Recommended To Complete Model:
Thin and Medium CA Glue
#11 Razor Blades and Hobby Knife
Sanding Block with 220 and 400 grit paper
Du-Bro 1-1/4 in. Wheels [DUB125MW]
2 AeroLITE PatchPak (Base Color)
1 AeroTRIM (Trim Color)
ParkZone PKZ3351 Ultra-Micro Receiver/ESC/Servo "Brick"
ParkZone PKZ3624 Motor and Gearbox
E-Flite EFL9051 Propeller
2 per package
Light weight design
1.10 gr. per wheel
Ideal for indoor and park flyers. Du-Bro RC Mini Lite Wheels are lightweight and features a 2 piece press together hub and a super light foam tire. Comes standard with .047 axle hole and can be drilled out for larger diameter axles.
These Mini Lite Wheels are sure to give your airplane that scale look.
This OEM ParkZone PKZ3352/U1152 Ultra Micro Receiver/ESC/Servo "puck" is a factory replacement unit for the ParkZone Vapor, Ember 2, HobbyZone Champ and many other Ultra-Micro model aircraft distributed by Horizon Hobby. The PKZ3352 is compatible with all ParkZone, E-Flite, HobbyZone, and Spektrum DSM2 compatible 2.4ghz transmitters. This product will not fuction with Airtronics, Futaba, Hitec, or other non DSM2 compatible transmitter.
The PKZ3352 weighs 3.3g and features an on-board receiver, electronic speed control (ESC), and servos mapped to Elevator (pitch) and Aileron (roll) transmitter channels. This configuration is Ideal for control of Rudder/Elevator three channel models. Two linear drive servos built atop a receiver/esc "puck" featuring a pre-soldered battery connector and motor plug.
Ultra Micro Propeller (2/pkg) - 130mm x 70mm. This propeller was designed for the E-Flite 4-Site and is same propeller used by the UM P-51 by ParkZone. Also recommended for all micro models by Stevens AeroModel that utilize the PKZ3624 Motor and Gearbox. Package includes one 130mm x 70mm propeller with foam rubber spinner.
(Note: propeller is installed by threading onto the output shaft of the pKZ3624 gearbox.)
These are a major upgrade for Eflite, ParkZone Ultra Micro and Kyosho Minium series micro RC models, and fit either without modification. With Hyperion's G3 technology inside, they deliver more mA per gram than the stock batteries, while sustaining higher voltage under high loads, for greatly improved power performance. Of course, like all Hyperion G3 Lipo they last for hundreds of cycles, with consistant performance, when properly charged and stored.
The fact that they can be safely charged at up to 5C rates - for charge times as low as 10 to 12 minutes - is just icing on a very tasty cake.
ZAP CA Is the thinnest CA in the ZAP product line. The penetrating or wicking ability of this glue makes it a favorite of modelers around the world. Balsa wood is bonded almost instantaneously, with the glue sometimes traveling several inches into the parts.
SUPERIOR PENETRATING FORMULA
SUPER THIN - WATER LIKE CONSISTENCY
BONDS AND CURES IN 1 TO 5 SECONDS
WORKS ON MOST MATERIALS
ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequaled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. Wood, plastic, metal, glass, ceramic, fabric, rubber, fiberglass, carbon fiber, or any combination of, ZAP-A-GAP CA+ can help solve many tough bonding problems.
SUPERIOR GAP FILLING FORMULA
MEDIUM VISCOSITY ALLOWS APPROXIMATELY 7 TO 10 SECONDS FOR PART POSITIONING
AVERAGE OF 20 SECONDS FOR CURING
WORKS ON OILY SURFACES
USE ZIP KICKER TO ACCELERATE CURE TIME
Flexi-Tips by ZAP brand CA glues fine tip is suitable for thin and medium weight CA and allows for Smaller Drops, Precision Application, Extension into hard-to-reach areas, Maximum use of bottle. Universal! fits most brand's CA bottles.
This a great little item. Sanding block is made from very high density foam and features fine 240 and extrafine 120 grit papers. This block won't deform and cause waves in your project like those cheap hardware store sanding sponges.
AeroLITE (SOLITE) Antique White, 11 in. x 27.5 in. (275mm x 700mm). Folded package.
Ultra light iron-on self-adhesive film (polypropylene) for electric indoor and micro model aircraft. Now offered in convenient PatchPak size; just the right amount for repair jobs, trim, or covering our micro and ultra-micro model aircraft kits. Transparent colors weigh only 20 grammes per square meter (0.60 ounces per square yard). 'Solid' colors are only slightly heavier. Weights include color and adhesive.
Film is folded into packages not rolled. Minor creases from packaging will readily iron out as film is applied to model.
QuickOats100 powered by a BL180 (the guts of a Beast) without landing gear for grass field handlaunches. It does consecutive loops from level, rolls, snaps, hammerheads and spins. What a gread small field plane.
Whether is shredding up the skies with the G480 or floating around at sunset with the Toon Rocketeer, Bill's kits are the most satisfying kits to build and fly. Keep up the great work!
— Scott Stevens
Outstanding! I just finished the Fokker D7 and gave it a test flight. I had not worked with balsa since I was a kid(too many years ago). Yours is the best kit I have ever seen. I purposely took my time because it was so enjoyable and I especially ...
— Fernando Engelsma
I have built everything from the catapult launched ThunderChuck to the Pterodactyl and Frede 2X and in every case find the same commitment to quality, performance and customer satisfaction. Stevens provides the highest value for money, best mater...
— John Harding
I love your models. In 2015, I have built and flown your 1911 Caudron, and am currently finishing the build of your Shaft 400. I purchased your Fullhouse for my winter project and was surprised to find your logo ball cap in the box. THANKS! It’s...
— Paul Mally
I bought a helium a year ago built this plane and flew it for about a year and love it. It was fun building this plane and I would recommend it to anyone who likes to build an fly it has been fun.
— Fred Carrigan
I would like to start by saying that I have been a customer for many years. I have always enjoyed every kit and they have all been very well designed and fly as expected and sometimes better! In my honest opinion it is your customer service that i...
— Gregg Hurla
Hi, I received my Helium mg2 kit yesterday, and I will have it ready for covering tonight. I have built a few laser cut kits but yours is the best by far. The accuracy of the parts fitting and the completeness and accuracy of the instructions is u...
— Tom Watson
I have to say that the MBP program is one of the best hobby investments I have made.
I finished building the Fly Baby, only thing I need is the radio block. This was another enjoyable kit to build, ...and am thinking about picking up another kit to start on. Good job guys, keep up the good work.
— Tony Scavello
I just got the Avro as the first of my model subscription plan. Really nice engineering!