SAVE 20% on Stevens AeroModel Brand Kits
(add the product to your shopping cart to apply the savings)
Come visit us this weekend at the AMA Expo East - Booth 432
Please note: Stevens AeroModel will be closed 2/20-2/27/2018 to attend the AMA Expo East in Secaucus, NJ. Orders placed while we are closed will be held to ship when we re-open on 2/28. Orders over $150.00 will receive free domestic shipping while we are closed. Can't join us at the show? Watch this space! Show specials will be made available online as well!
| Stevens AeroModel presents the FREDe (1.5X) weighing in at less than 2 lbs flying weight and featuring over twice the wing area of our original FREDe parkflyer! The FREDe 1.5X is a true AMA legal giant park flyer with 600 square inches of thick
under-cambered wing, a svelte 31 oz flying weight, and 120W/lb power
loading. FREDe 1.5X an ideal park flyer for larger parks and school yards.|
FREDe™ is a ToonSCALE™ version of Eric Clutton's F.R.E.D. (Functional Runabout Experimental Design) FREDe's airframe frames quickly thanks to precision laser cut components and simple yet thoughtful engineering. This rugged design features our shock mounted landing gear system and soaks up all the bumps and bruises a beginner can deliver. FREDe™ dishes out stable predictable performance with pro pleasing "fun" on tap allowing for all rudder, elevator, throttle aerobatics including flat and falling leaf flat spins! FREDe™ - because flying should be FUN!
Motor - SA Sport BL.10 (similar to A30-16M Hacker)
Propeller - APC 12x6 SF
Battery - 2S 7.4V 2100 25C LiPo (Hyperion G3 2100 7.4V)
ESC - High Quality 30A ESC (SA Sport 30A Brushless ESC)
SERVOS - 2 Micro Servos (Hitec HS-82MG)
Suggested Finishing Items:
Trexler #10 Balloon Wheels or similar 3-1/2 inch diameter foam wheel.
3-4 Rolls AeroLITE covering
Sanding Bar with 250, 400, and 600 grit paper
Sharp Hobby Knife with #11 blades
5 or 30 Min Epoxy
1 oz of Thick, Medium, and Thin CA glues
Special Instructions: Never exceed the recommended battery voltage listed on the package. Do not use a separate battery supply with this controller. Never disconnect the battery supply when the motor is running.
This product is guaranteed to arrive to you operational, beyond that no additional warranty, guarantee of suitability, offer of service, or replacement is provided. We allow 30 days from the date of purchase for the end user to verify the function of this product and make a warranty claim.
Trexler size 10G pneumatic latex balloon wheels. Heavier gauge rubber than sizes 1-6. Product Inflates to 3-1/2 in. diameter, sold in pairs, and is suitable for larger gas and electric models with a maximum airframe weight of 12 lbs. Made right here in U.S.A. just like they always have been!
Trexler do's and don'ts:
DO NOT - Inflate using your mounth. Moisture from your lungs/mouth will cause the valve stem to seal rendering the product useless.
DO NOT - Leave inflated while in storage, again the valve stem may seal due to moisture within the tire.
DO NOT - Over-inflate tire with pump as tire will rupture or blister. Trexler wheels (#1-#6) are best inflated using a glue syringe.
DO NOT - Disount tire from wooden hub as you might damage or puncture the tire.
DO NOT - Use on models heavier than specified by Trexler.
DO - Store in a cool, dry, dark place.
DO - Inflate tires prior to use using the Trexler inflator or large capacity syringe.
DO - Deflate tire after each flying session and leave the valve stems open.
DO - Adhere to the suggested carrying capacity of the tires when sizing to fit your model.
Ordering Instructions: 1) Prior to adding this item to your cart fill in the form below titled "Enter Kit and Sheet Number" with the model airplane kit and desired sheet number you wish to re-order. (Every Stevens AeroModel kit has the sheet number or sheet ID engraved on the cut sheet and/or listed in your product manual.) 2) Order one unit of this product per full laser cut sheet required. Thus, if you need to order multiple sheets or multiple copies of a single sheet, the order quantity of this item must match your requested sheet count. 3) Please be aware that this item is cut to order and will add 3-5 business days to the processing of your order.